PST BRIDGE PRO EVALUATION MODE MAC
PST BRIDGE PRO EVALUATION MODE WINDOWS

Connection Method вЂ“ Select Original Source IP.

Create a Pass access ruleВ with the following settings:.

Create an Access Rule for Local BridgingДЄfter configuring the local bridge, you must create an access rule to allow traffic across the bridge and use the advanced traffic inspection features of the firewall.

Perform a Failsafe Network Activation ( Control > Box).

Scroll to the top and find the Ethernet adapter Local Area Connection settings.

PST BRIDGE PRO EVALUATION MODE WINDOWS

If you have a DHCP address, enter the following at the Windows command line:ДЄll of the network configurations display on the screen. If you have a DHCP address, your information will not display. If you have a staticВ IP address, information including the default route and DNS information is displayed. Select your LAN adapter and click the IPv4 properties. To get the gateway of the LAN before you disconnect your computer from the LAN, go to Control Panel > Network and Sharing > Change adapterВ settings on your workstation. For example, enter 10.17.11.55 or an IP address that is relative to your network.Д«ridge IP Netmask вЂ“ Netmask for the gateway. Bridge IP Address вЂ“ IP address for the gateway.In the entry, specify the following settings for the gateway. Bridge IP Address вЂ“ In this table, add an entry or edit an existing entry for the gateway to assign an IP address to thisВ bridging group.

PST BRIDGE PRO EVALUATION MODE MAC

If the MAC address must not be changed, select DenyвЂ“MACвЂ“Change.

MAC Change Policy вЂ“ To specify if the MAC address of the interface can be changed, select AllowвЂ“MACвЂ“Change (default).

Unrestricted MACs вЂ“ List of MAC address for which the Allowed Networks (ACL) does not apply.

For example, enter 0.0.0.0/0 in the configurations for port 2 and port 3. You can enter complete networks, individual client/server IP addresses, or network ranges.

Allowed Networks (ACL) вЂ“ Networks that are allowed to communicate over the bridged interface.

For VLANs, enter the physical VLAN interface and the VLAN tag separated by a dot.

InterfaceВ вЂ“ The exact network interface label, as listed in the network configuration.

For example, add entries for port 2 and 3.ДЇor each interface, you can specify the following settings:

Bridged Interfaces вЂ“ In this table, add all of the interfaces that must be bridged together in this group.

In the Bridged Interface Group table, add a group:.

In the left menu, select Layer 2 Bridging.

Verify the Location is configured correctly.

Select Wi-FiВ from theВ ConfigurationВ menu in the left menu.

For CloudGen Firewalls with built-in Wi-Fi:.

Go to CONFIGURATION >В Configuration Tree > Box > Network.

These instructions also provide example settings that assume that your workstation is connected to port 1 and that you are creating a bridge between port 2 and port 3.

DHCP Server вЂ“ Make sure that DHCP server and DHCP client are disabled.

Otherwise, IP configurations involving Wi-Fi interfaces are not possible.

Wi-Fi вЂ“ For CloudGen Firewalls with built-in Wi-Fi, the Country must be selected.

Firewall вЂ“ It is assumed that port 1 is the management port and the default management IP 192.168.200.200 listens on this interface.

To make the connection transparent, you must configure a local bridge and create an access rule to allow traffic between the bridged interfaces.Д«efore configuring a local bridge, make sure that the following services are correctly configured: This configuration allows you to explore the firewall's advanced traffic and application inspection features by using traffic that your workstation generates on the LAN. Use a local bridge to transparently connect your local workstation with the network across a Barracuda CloudGen Firewall.

Pst bridge pro evaluation mode